EXSYS LowProfile 2S PCI Serial RS-232 card Manuel d'installation télécharger pdf

If you are ready with the jumper settings, please proceed with the following installation

instructions. Because the designs of computers are different, only general installation

instructions are given. Please refer your computer’s reference manual whenever in doubt.

1. Turn off the power to your computer and any other connected peripherals.

2. Remove the mounting screws located at the rear and/or sides panels of your Com-

puter and gently slide the cover off.

3. Locate an available expansion slot and remove its covers from the rear panel of your

computer. Make sure it is the right expansion slot for the card (see card description)

4. Align the card with the expansion slot, and then gently but firmly, insert the card.

Make sure the card is seated and oriented correctly. Never insert the card by force!

5. Then connect the card with a screw to the rear panel of the computer case.

6. Gently replace your computer’s cover and the mounting screws.

HARDWARE INSTALLATION :

6 5

CHECK THE INSTALLED DRIVER:

Click at Start<>Run< then enter “compmgmt.msc“ and click at >OK<. In the windows

that open select >Device Manager<. Under „Ports (COM and LPT)“ you should find

one or more new ”PCI Ports“ as sample (COM3). If you see this or similar entries the

card is installed correctly.

CHANGE PORT NUMBER:

If you like to change the port number for example COM 3 to COM5, open the >Device

Manager< click at >COM3<, >Settings< and then >Advance<. There you can change

between COM 3 to 256.

Windows NT 4.0:

Start Windows NT and insert the driver CD into your CD-ROM drive (for example D:).

Click at >Start< >Run< and enter „D:\IO\OXFORD\NT4\Install_Serial.exe" then click

>OK<. Windows NT will now start the setup program and install the driver. Please

Restart Windows NT after installing the drivers.

CHECK THE INSTALLED DRIVER:

Click at >Start< >Programs< >Administrative Tools[Common]< >Windows NT-

Diagnostics< then click at >Resource< >IRQ<. Here you should find the entry „09

oxser 0 PCI“. Then click at >I/O-Port< here you should see the entries „D400-D407

oxser 0 PCI“ „D800-D802 oxser 0 PCI“ and „DC00-DC1F oxser 0 PCI“

for the ports. The I/O addresses can change depends which system and card is in-

stalled. If you see these or similar entry's the card is installed correctly.

LINUX:

There are no drivers available for Linux, but the card is supported by the most versions

of Linux. Because each individual distribution and kernel version of Linux is different,

sadly we cant provide a installation instruction. Please refer to the installation manual

for standard IO ports from your Linux version! In some newer versions the card will

even be installed automatically after starting Linux.

JUMPER EINSTELLUNG & ANSCHLÜSSE:

Die EX-43392 ist eine PCI serielle RS-232 Karte mit zwei seriellen FIFO 16C95x Ports,

für den Anschluss von High-Speed seriellen RS-232 Peripherie Geräten (z.B. Terminal,

Modem, Plotter usw.). Sie unterstützt den 32 und 64-Bit PCI bzw. PCI-X Bus mit 5 Volt

und 3,3 Volt. Es ist nicht möglich die I/O Adressen und Interrupts manuell einzustellen,

da die Einstellungen der Karte vom System (BIOS) und beim Installieren des Betriebs-

systems automatisch vorgenommen werden. Es besteht bei Bedarf die Möglichkeit, +5V

- oder +12V auf einen von vier Pins der beiden 9 Pin Stecker zu legen (POS System).

BESCHREIBUNG & TECHNISCHE DATEN :

AUFBAU :

Kompatibilität: PCI & PCI-X 3,3Volt & 5Volt bei 33Mhz

Betriebs Systeme: WIN 9x/ME/NT4.0/2000/XP/Server 2003/Vista/(Linux vom OS)

Anschlüsse: 1 x 44 Pin Buchse für Octopus Kabel mit 2 x 9 Pin Seriell D-SUB Stecker

Lieferumfang: EX-43392, Treiber CD, Deutsche Anleitung, Standard Bracket

Zertifikate: CE / FCC / RoHS / WEEE DE97424562 / WHQL

DRIVER INSTALLATION :

Windows 9x/ME/2000/XP & Vista:

After starting Windows it recognizes a new “PCI Controller“ and open the hardware

assistant. Please choose manual installation and put the driver CD into your CD-Rom

drive. Now enter the Path "D:\IO\OXFORD\" and then the directory of your operating

system “95_98_ME“ “2000“ “XP32“ “XP64“ “Vista32“ or “Vista64“ into the box for

the Path/Source and click at >next/continue<. Now Windows search for the drivers in

the specified directory. Follow the hardware assistant and finish the installation. If

Windows recognizes other new devices repeat the above described steps. Attention!

Restart Windows in any case after installing the drivers.

CHECK THE INSTALLED DRIVER:

Click at Start<>Run< then enter “compmgmt.msc“ and click at >OK<. In the windows

that open select >Device Manager<. Under ”Ports (COM and LPT)“ you should find

one or more new ”PCI Ports“ as sample (COM3). If you see this or similar entries the

card is installed correctly.

CHANGE PORT NUMBER:

If you like to change the port number for example COM 3 to COM5, open the >Device

Manager< click at >COM3<, >Settings< and then >Advance<. There you can change

between COM 3 to 256.

Windows Server 2000/2003:

After starting Windows it recognizes a new “PCI Controller“ and open the hardware

assistant. Please choose manual installation and put the driver CD into your CD-Rom

drive. Now enter the Path "D:\IO\OXFORD\" and then the directory of your operating

system for Server 2000: “2000“ and for Server 2003: “XP32“ or “XP64“ into the box

for the Path/Source and click at >next/continue<. Now Windows search for the drivers

in the specified directory. Follow the hardware assistant and finish the installation. If

Windows recognizes other new devices repeat the above described steps. Attention!

Restart Windows in any case after installing the drivers.

S1+S2:

44 Pin Buchse für den

Anschluss des Octopus-

Kabel (2 x 9 Pin)

Seriell Chip 16C952

JP5: +5V oder +12V

einstellbar auf

den 9 Pin von S1

J2: Anschluss vom

PC Netzteil für

+5V oder +12V

Spannung

JP 3: Umschaltung der

Spannung von

PCI-BUS auf

PC-Netzteil

JP4: +5V oder +12V

einstellbar auf den

9 Pin von S2

+5V

+12V

Dis

Pin 1

Pin 4

Pin 8

Pin 9

JP3:

PCI AUX

JP3 auf PCI = +5 or +12V

kommt vom PCI BUS

JP3 auf AUX = 5 oder +12V

kommt vom PC Netzteil

Mit der EX-43392 haben Sie die Möglichkeit +5V- oder +12V auf einen der folgenden

vier Pins, des 9 Pin Steckers S1 und S2 zu konfigurieren :

Achtung !! Nur konfigurieren wenn für das Peripheriegerät auch +5Volt oder +12Volt

gebraucht wird. Für normale Anwendungen, Jumper nicht verändern.

+5V

+12V

JP4 & JP5:

(S1 + S2)

Bedienungsanleitung

Vers. 1.0 / 03.12.08

1 +5V

2 GND

3 GND

4 +12V

J4: Wenn JP3 auf AUX gestellt ist muss J2 mit dem Stromanschluss vom

PC Netzteil verbunden werden! Bitte auf die richtige Polarität achten!

Achtung! Stecker nie bei eingeschaltetem PC ein oder ausstecken!

43392

English

43392

English

JUMPER SETTING & CONNECTORS:

DB9M:

Pin Signal Pin Signal Pin Signal

1 CDC 4 DTR 7 RTS

2 RXD 5 GROUND 8 CTS

3 TXD 6 DSR 9 RI

Serial 9 Pin D-SUB male connector (S1 and S2):

1 2

Bedienungsanleitung 1
User Manual 2

Résumé du contenu

Page 1 - Bedienungsanleitung

If you are ready with the jumper settings, please proceed with the following installation instructions. Because the designs of computers are different

Page 2 - User Manual

2 3 4 The EX-43392 is a plug & play high-speed serial RS-232 expansion card for the PCI & PCI-X Bus. The EX-43392 provides two 9 pin high spee

Commentaires sur ces manuels

Pas de commentaire

EXSYS LowProfile 2S PCI Serial RS-232 card Manuel d'installation

Naviguer en ligne ou télécharger Manuel d'installation pour Cartes/adaptateurs d'interface EXSYS LowProfile 2S PCI Serial RS-232 card. EXSYS LowProfile 2S PCI Serial RS-232 card Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Cartes/adaptateurs d'interface EXSYS LowProfile 2S PCI Serial RS-232 card