EXSYS EX-11494 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Cartes/adaptateurs d'interface EXSYS EX-11494. EXSYS EX-11494 Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 2
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Please note the following installation instructions. Because there are large differences
between the PC’s, we can give you only a general installation instructions for the
EX-11494. Please refer your computer’s reference manual whenever in doubt.
1. Turn off the power to your computer and any other connected peripherals.
2. Remove the mounting screws located at the rear and/or sides panels of your Comput-
er and gently slide the cover off.
3. Locate an available PCI-Express expansion slot and insert the card. Make sure that
the card is plugged in correctly.
4. Now install the power supply via the 4 pol molex connector or the SATA 15 pin con-
nector. (see picture Connectors JP4 or JP5)
5. Then attach the card with a screw to the rear panel of the computer.
6. Gently replace your computer’s cover and the mounting screws.
HARDWARE INSTALLATION
6 5
EXEXEX
-
-
-114941149411494
EnglishEnglishEnglish
EXEXEX
-
-
-114941149411494
EnglishEnglishEnglish
1
Die EX-11494 ist eine USB 3.0 4 Port Quad Channel PCI-Express Karte. Sie ist mit 4 externen
Port‘s ausgestattet, die jeweils 900mA Strom zu Verfügung stellen. Sie unterstützt alle PCI-
Express Slots von x1 bis x16. Der serielle PCI-Express Bus unterstützt optimal die Leistung des
schnellen RENESAS Chipsatz. Zusätzlich besitzt jeder einzelne USB 3.0 Port einen eigenen
Chip und somit auch einen eigenen Channel. Die EX-11494 gewährleistet so eine sichere
Datenübertragung und exzellente Performance von bis zu 5Gbit pro Sekunde an jedem Port!
Es ist nicht möglich die I/O Adressen und Interrupts manuell einzustellen, da die Einstellungen
der Karte vom System (BIOS) und beim installieren des Betriebssystems automatisch vorge-
nommen werden. Die EX-11494 benötigt zusätzlichen Strom vom PC Netzteil, um die volle
Leistung von 900mA an den 4 externen Port‘s zu gewährleisten.
BESCHREIBUNG & TECHNISCHE DATEN
AUFBAU
DRIVER INSTALLATION
BedienungsanleitungBedienungsanleitung
Vers. 1.0 / 07.11.12
ANSCHLÜSSE
RENESAS Chip-Set
J1-J4:
4 x externe
USB 3.0 A-Buchse
JP4:
Molex Power
Anschluss vom
PC-Netzteil
JP4:
1 +12V 2 GND 3 GND 4 +5V
Kompatibilität: PCI Express x1 bis x16
Betriebssysteme: Windows XP/ Vista/ 7/ 8/ Server 2008 R2
Anschlüsse: 4x USB 3.0 A-Buchse extern, 1x 4 pol Molex, 1x SATA 15 pin Stecker
Lieferumfang: EX-11494, Treiber CD, Anleitung
Zertifikate:
CE
CE CE
CE / FCC / RoHS / WEEE DE97424562 / WHQL
JP5:
SATA 15 pin
Power Anschluss
vom PC-Netzteil
Um die EX-11494 zu betreiben, muss die Karte mit
dem Stromanschluss vom PC Netzteil verbunden
werden! Es darf nur ein Stromanschluss verwendet
werden JP4 ODER JP5!
Bitte auf die richtige Polarität achten!
Achtung! Stecker nie bei eingeschaltetem PC ein
oder ausstecken!
J1-J4:
USB 2.0 Pin‘s
Pin Signal
1 VCC
2 DATA-
3 DATA+
4 GND
USB 3.0 Pin‘s
Pin Signal
5 SSTX+
6 SSTX-
7 GND
8 SSRX+
9 SSRX-
CONNECTORS
JP5:
Pin Assignment Pin Assignment
1 3.3 Volt (Orange) 7 5 Volt (pre-charge)
2 3.3 Volt (Orange) 8 5 Volt (Red)
3 3.3 Volt (pre-charge) 9 5 Volt (Red)
Pin Assignment
13 12 Volt (pre-charge)
14 12 Volt (Yellow)
15 12 Volt (Yellow)
4 Ground (Black) 10 Ground (Black)
5 Ground (Black) 11 Reserve
6 Ground (Black) 12 Ground (Black)
For using the EX-11494 you must connect the card with the PC power supply. It must be
connected only one power connector JP4 OR JP5! Please make sure you connect the plug in
the right direction.
Never connect or release the plug while the PC is supplied with power!
ÜBERPRÜFEN DES INSTALLIERTEN TREIBER:
Open the >Device manager<. Now you should see at „USB-Controller“ the following new
entry's:
If you see this or a similar information the device is installed correctly.
DRIVER INSTALLATION
Windows XP/ Vista/ 7/ Server 2008 R2:
After starting Windows is recognizes a new “USB (Universal Serial Bus)-Controller“. Start
the „SETUP“ file which is in the “uPD720201_202” folder (see picture):
Follow the installation instructions and complete the installation.
Windows will now install automatically you right driver for your particular operating system. After
the installation the operating system detects the card and automatically install them.
Vue de la page 0
1 2

Résumé du contenu

Page 1 - USB 3.0 Pin‘s

Please note the following installation instructions. Because there are large differences between the PC’s, we can give you only a g

Page 2 - User ManualUser Manual

2 3 4 EXEXEX---11494 11494 11494 DeutschDeutschDeutsch EXEXEX---114941149411494 DeutschDeutschDeutsch The EX-11494 is a plug & play h

Commentaires sur ces manuels

Pas de commentaire