EXSYS EX-3455 Manuel d'utilisateur télécharger pdf (Page 5)

EX-3455 Backup System SATA2 RAID 0/1

Seite 20

EZ-RAID 1 Installation (If an existing hard disk with data)

1. Power off your System before proceeding with any Installation.

2. Install the EX-3455 according to the instructions on page 5 and 6

3. Important !!! Please back up the data on your Source Drive to prevent from any data loss

caused by accidentally connecting it to any wrong connector.

4. Review the DIP switch setting and make sure it is set in EZ-RAID 1 mode and the Pin 4 of the

DIP Switch is ON.

5. Connect the Upstream SATA HOST Connector of the RAID Controller to your motherboard’s or

SATA add-in card’s SATA Host Connector.

6. Connect your Source Drive to M0 (Down) Connector of the RAID Controller. Please

7. Connect your Destination Drive (blank drive) to M1 (UP) Connector of the RAID Controller,

please make sure the Destination Drive has bigger capacity than the Source Drive.

8. Power up the system, you will hear a beep from the RAID Controller and it will start copying the

data from M0 to M1 drive automatically. Since this operation was doing in the background, all

installation is finished.

9. Set the DIP switch Pin 4 to Off to prevent from changing the RAID mode accidentally.

6. RAID Installation

RAID 1 Installation (Only for two new hard drives)

1. Power off your System before proceeding with any Installation.

2. Important !!! This mode will erase all data on the drives that connected to the RAID Con-

troller to build up a fresh mirroring disk array set, please back up their data before pro-

ceeding the following installation.

3. Review the DIP switch setting and make sure it is set in RAID 1 mode and the Pin 4 of the DIP

Switch is ON.

4. Connect the Upstream SATA HOST Connector of the RAID Controller to your motherboard’s or

SATA add-in card’s SATA Host Connector.

5. Connect one SATA drive to M0 (Down) Connector of the RAID Controller.

6. Connect the other SATA drive to M1 (Up) Connector of the RAID Controller. Please note that if

the two drives have different capacity, then the RAID Controller will automatically truncate the

bigger drive to the same capacity as the smaller one.

7. Power up the system, you will hear a beep from the RAID Controller and both M0 and M1 drive

are configured as the RAID 1 (mirroring) mode. In this mode, the disk array is blank and you

need to do partition and format by your operating system.

8. To partition a RAID set bigger than 2TB (Terabyte), you need to partition it with GPT (GUID

Partition Table) format instead of MBR (Master Boot Record). The GPT can support up to 18

EB (Extrabyte, equals to 1,000 Terabytes).

9. Set the DIP switch Pin 4 to Off to prevent from changing the RAID mode accidentally.

Backup System SATA2 RAID 0/1 EX-3455

Seite 5

3. Hardware Installation

3.1 Fronteinbau in einen 3.5-Zoll Schacht

3.2 Fronteinbau in einen 5.25-Zoll Schacht

Da jedes Computer Gehäuse verschieden aufgebaut ist, können wir ihnen nur eine Information

geben wo die Befestigungslöcher der EX-3455 sind.

Befestigung im PC Gehäuse mit den

mitgelieferten Gewinde-Schrauben

Befestigung im PC Gehäuse mit den

mitgelieferten Gewinde-Schrauben

Legen sie den 3.5-Zoll Rahmen in den 5.25-Zoll Rahmen und befestigen diesen mit den mitgliefer-

ten Gewinde-Schrauben

Befestigung den 3.5“ Einschub mit den vier

Gewinde-Schrauben am 5.25“ Rahmen

Den 5.25“ Rahmen wird dann mit

den vier Blech-Schrauben am PC

-Gehäuse befestigt

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

EXSYS EX-3455 Manuel d'utilisateur Page 5

Commentaires sur ces manuels

Produits connexes et manuels pour Contrôleurs RAID EXSYS EX-3455